Menu Close

Panasonic KX-UDS124

Requirements

General Information

In this article we will explain how to configure a Panasonic KX-UDS124 with peoplefone Hosted. For the configuration of a mutlicell system, you need access to the webinterface of the two or more devices. First step, enter the server settings, so the device can connect to peoplefone and in a further step, we will put in the credentials for authentication. After that we will explain how to configure a mutlicell system.

peoplefone Connection

Standard Credentials

Username: admin
Password: adminpass

SIP Settings

Webinterface → Panasonic KX-UDS124 → VoIP → SIP Settings

  • Type in the registrar server adress
  • Type in the server port
1 PanasonicKX-UDS124 SIP-Settings.PNG

VoIP Settings-PS

Webinterface → Panasonic KX-UDS124 → VoIP → VoIP Settings-PS

  • Click on Line# SIP Setting
1 PanasonicKX-UDS124 SIP-SettingsPS.PNG
2 PanasonicKX-UDS124 SIP-SettingsPS.PNG

PS Registration

Webinterface → Panasonic KX-UDS124 → System→ PS Registration

  • Enter a PS Name
  • Click on start PS registration
  • Connect your handset to your basestation (MT Registration)
1 PanasonicKX-UDS124 System PS-Registration PS-Name.PNG

Codecs

Webinterface → Panasonic KX-UDS124 → VoIP → VoIP Settings → Codecs

  • Put the codecs into the right order: PCMA, PCMU, G722, G729A, G726-32 is deactivated.
1 PanasonicKX-UDS124 VoIP-Settings Codecs.PNG

Multicell System

In order to operate a multicell system, please consider two things:

  • Same Firmware version on both DECT-stations
  • Same time configuration

Configuration «DECT Master»

Network

Webinterface → Panasonic KX-UDS124 → Network

  • The first SIP-sender must have a static local IP-adress with the following settings:
  • Connection Mode: Static
  • Static IP Address: IP-adress from the network
  • Subnet Mask: Own subnet mask
Network.PNG

Time Adjust Settings

Webinterface → Panasonic KX-UDS124 → System → Time Adjust Settings

  • Define the automatic time setting and daylight saving time
Time.PNG

CS Name

Webinterface → Panasonic KX-UDS124 → System → CS Name

  • A name will be assigned to the first zone
  • You can use the purpose of the zone as it’s name
CSName.PNG

Air Settings

Webinterface → Panasonic KX-UDS124 → System → Air Settings

  • Define the super master DECT sender
  • The first DECT sender is a super master, which serves as a central access point. This setting have to be applied.
AirSettings Dect1.PNG
  • CS Class: Master
  • Super Master IP-Adress: Own IP-adress

CS Management

Webinterface → Panasonic KX-UDS124 → System → CS Management

  • Start the registration of further DECT senders in that zone
  • Add another DECT sender, start the CS registration on the master sender

Configuration «DECT Slave»

Air Settings

Webinterface → Panasonic KX-UDS124 → System → Air Settings

  • Configure the new DECT sender
AirSettings Dect2.PNG

The new sender will be integrated into the network as a DHCP-device. It can also have a static IP, but doesn’t have to. Under “System” “CS Name” you can give the sender a name.

On  “Air Settings” the following settings have to be set:

  • CS Class: Slave
  • IP Adress: IP-adress according to the network configuration of the master

CS Management

Webinterface → Panasonic KX-UDS124 → System → CS Management

  • Now the DECT sender will be shown in the CS management.
  • Registering of a DECT Handset
    • The DECT handsets will be activated over the PS registration.
CSmanagement Dect2.PNG